PCB

LibreServo v2.3.1. Release Version

LibreServo has finally reached the first final Hardware release (version 2.3.1)!

It has been a long road and there is still a long road ahead, but now on the software side. LibreServo will not stop here and later on there will come new projects that make use of LibreServo, like a possible 3D biped robot, but all of that will come in the future and all of it will be announced here so let's stop the guessing and talk about the now.

Production Files

Generally the final production of a PCB is exactly the same as the gerber files we have generated, but there are times when there is a doubt if the production is going to be exactly the same as we want, for example if we have a tinned slot, or if we have epoxy filled vias and we want to make sure we meet the specifications as we saw in the article on last minute changes in LibreServo. In all these not so usual cases, in JLCPCB we have the option to check the production files before our PCB goes into production. Be careful! we will only have 24 hours to confirm the production files, otherwise they will autoconfirm, so don't lazy.

🎉I have already sent to manufacture the final version of LibreServo to JLCPCB!🎉
In total there have been 50 PCB boards (50 because they were the same price as 30) of 0.8mm thick and of the highest possible quality; 6 layers, ENIG finish, epoxy filled and capped vias, PCB material upgraded to FR-4 TG155... Everything came out to me for about $93.24, which with VAT and shipping goes up to $118.18. That gives a base price of about $2.36 per LibreServo. Making the four-layer version of LibreServo, in HASL finish (with lead), FR-4 TG135-140 material and tracks simply covered with solder mask comes out to $56.20, which with VAT and shipping goes up to $75 for a total of $1.5 each LibreServo. Personally I think that making it in 6 layers and the rest of the improvements are well worth 0.86$ per board, but it is something that each one will have to value and that certainly LibreServo is going to work equally well in both configurations.

LibreServo v2.3 PCB

A few days ago I presented LibreServo version 2.2 and announced that I had one last final change... this time the wait has not been long and I bring the new version of LibreServo, version 2.3.
This version should already be the final hardware version of LibreServo .
The biggest change that LibreServo has had in this latest version with respect to the previous one is the H-bridge. Risky move seeing what it cost me to make it work but I think it will be a remarkable improvement and the missing component to make LibreServo the definitive option.

LibreServo v2.2 PCB

Pre-final version. This was going to be the final version, was going to be, because in the end it is not going to be.

• The oscillator has been changed for a more compact one.
• The position of several components has been slightly reworked
• Ground planes have been generated on the outer layers
• The position of the silk-screen printing has been repositioned with the idea that the vias will be capped and it will be possible to silkscreen on top of them
• The PCB has been narrowed by a few tenths of a millimeter to fit perfectly to the servomotors
• The two PCBs have been joined by using mouse-bites

In general, they are all small changes, but... just before placing the order I went back to review each and every one of the components, and there is one that I have decided to change and it is a very important one that has been in LibreServo from the beginning. In the next article I will unveil the final change 😉

New LibreServo v2.1

A few days ago I received the LibreServo boards I had ordered from JLCPCB. As I told you in the article of changes in LibreServo v2.1, the new version of LibreServo added two extra layers to reach the 6 layers and thus have the offer of JLCPCB and after receiving them and see them ... I only have words of absolute amazement.

The result is magnificent, not only the gold finish looks great in it 😎, the silkscreen itself is much better than when you order plates of four layers or less and the tracks filled with epoxy and covered in copper give an extraordinary result, not only at electrical/routing level and for soldering is a huge improvement, but also allows silkscreen printing on top of vias without any problem, which in LibreServo with the philosophy that has to point all the components to facilitate then when soldering, it comes great.

LibreServo v2.1 PCB

These schematics will not last long because new changes have already been made and will be sent to manufacture in the coming days if all goes well. The order of the next version will coincide with the Chinese vacations, but I hope not to have any problem except some small delay already announced by the manufacturer JLCPCB.

In this LibreServo version, the main PCB, goes from 4 to 6 layers because JLCPCB, as we mentioned in the article of changes in LibreServo v2.1, has made a very aggressive offer in which it is cheaper to manufacture a 6-layer PCB instead of 4, taking into account that in 6 layers you get for free the ENIG finish (in gold) and the vias are filled and covered, in other words, a totally professional finish. It is a really crazy offer.

Despite all this, of course LibreServo will maintain full compatibility with 4 layers and only when generating the gerbers the central layers are removed and the matter is solved.

LibreServo v2 PCB

I had pending for months to upload the schematics to the web. The schematics are exactly the same with which I made the LibreServo v2 PCBs but with the texts corrected in position so they read better.

In previous posts as you can read in the article of the first LibreServo test board and in the conclusions of the second LibreServo test-board, the LibreServo changes were massive in each and every aspect. Virtually every component was overhauled and moved to a two PCB, four-layer design.

Soldering the first LibreServo v2

This little entry is to announce that the new LibreServo has arrived, I was able to solder it without any problem and it is fully working! 🥳

After the tests I did with the test boards v1 and v2 many changes were made to the design of LibreServo. Because of those many changes, LibreServo moves to version 2.

LibreServo sending data via RS485 to Arduino plotter

After several tests, the LibreServo hardware is finally chosen and it's working, even the H-bridge that gave me a lot of problems! In general, all the parts of LibreServo remain as they were, because they were already working correctly, except the parts are discussed in this article.